01
Lightweight 960mm cabinet
The aluminium profile frame weighs 21kg and uses stainless steel quick locks for fast assembly and consistent panel flatness.
Outdoor Fixed LED960 × 960 Cabinet
Outdoor P4
A 960 × 960mm aluminium cabinet with a 480 × 320mm module, built for close-to-mid outdoor walls with 6,000–12,000 nit output.
4mm
Pixel pitch
6,000–12,000 nits
Brightness
3,840–7,680Hz
Refresh rate
Product overview
Outdoor P4 uses the 960 × 960 cabinet family: a 960 × 960mm aluminium frame carrying eight 480 × 320mm modules in a 2 × 4 layout. At 21kg, the cabinet is lighter than a 1m steel box, which reduces transport and installation cost while keeping front and rear service access.
Every unit is assembled and tested in Shenzhen before packing. Cabinet drawings, pixel map and control-system settings are supplied with the shipment, so the configuration on site matches the quotation.
Building facadesRetail entrancesRoadside mediaTransport hubs
Specifications
- Pixel pitch
- 4mm
- Brightness
- 6,000–12,000 nits
- Refresh rate
- 3,840–7,680Hz
- Avg power
- 200–300 W/m² avg
- Cabinet size
- 960 × 960 × 88.5mm
- Cabinet weight
- 21kg
- Module size
- 480 × 320mm
- Module resolution
- 120 × 80
- Pixel density
- 62,500 dots/m²
- Pixel structure
- SMD1921
- Module quantity
- 2 × 4
- Grayscale
- 16-bit
- Frame rate
- 50/60Hz
- Cabinet resolution
- 240 × 240
- Contrast ratio
- 15,000:1
- Viewing angle
- 160° horizontal / 140° vertical
- Max power
- ≤800 W/m²
- Input voltage
- AC90–264V, 47–63Hz
- Operating temperature
- -20°C to +60°C / 10–85% RH
- Protection
- IP65 front and rear
- Maintenance
- Front and rear service
Advantages
Engineering decisions behind Outdoor P4, and what they change on site.
02
480 × 320mm module
Eight modules per cabinet create a 240 × 240 pixel cabinet, with the module handle and hub board accessible from the rear.
03
Energy-saving drive
Average power is 200–300 W/m² and maximum power is 800 W/m², keeping the electrical load predictable for larger walls.
Outdoor P4
Structure introduction
Outdoor P4 is built around a sealed 960 × 960 × 88.5mm cabinet. The front module, gasket, rear cover and pressure path are designed as one weather system, so rain, dust and thermal expansion do not open a path into the electronics.
960 × 960 × 88.5mm
01
IP65 sealed enclosure
A continuous gasket runs around the module and rear cover. Cable entries use sealed glands, and the cabinet is tested before packing.
02
Module and heat sink
The LED module sits against a thermal path that spreads heat across the cabinet back. The heat sink is isolated from the sealed electronics chamber.
03
Power and control chamber
Power supplies and receiving cards are mounted in a protected chamber with a separate service cover, keeping water away from live connections.
04
Mounting and wind load
Mounting points are sized for the cabinet weight and site wind load. The structure is confirmed against the installation height before production.
Outdoor P4 · Outdoor fixed installations
Outdoor fixed project cases
Corner walls, retail cubes, curved night displays and highway billboards. Each installation is shaped by viewing distance, structure and the service route.
06 case views
Selected outdoor fixed installations. Final cabinet, brightness and service layout follows the site survey.
01Building corner wall
Two faces meet at a sharp building corner above street level. The cabinet layout follows the edge, keeping the image continuous through the bend.
02Retail corner cube
A compact two-face cube sits above a storefront, carrying brand content at close viewing distance while keeping the shopfront visible.
03Curved night corner
A curved corner wall follows the building line and stays readable against surrounding shop lighting. Automatic dimming keeps the night image balanced.
04Corner media wall
A large corner wall combines several faces above a busy street, with sealed cabinets and a service route planned for the structure.
05Highway billboard
A double-column steel structure carries a long-throw LED billboard, specified for direct sun and viewing from passing traffic.
06Midtown corner wall
A flush corner wall above a hotel entrance carries high-brightness content at close-to-mid viewing distance, with front or rear service access.
Planning a similar outdoor wall? Send the wall size, viewing distance and mounting structure.
Discuss a similar projectDesign details
The decisions that affect how Outdoor P4 looks, installs and stays serviceable on site.
01
Water path, not just a gasket
The cabinet is shaped so water runs away from the module seam. Service covers overlap the opening rather than sitting flush, which is what keeps a facade dry in driving rain.
02
Daylight brightness
6,000–12,000 nits output is paired with automatic brightness control, so the wall stays readable at noon without glare at night.
03
Thermal expansion
Module and cabinet materials are selected to expand together. The module fixing allows controlled movement instead of stressing the LED board.
04
Anti-corrosion finish
Cabinet surfaces are coated for humid and coastal sites. Fixings and grounding points are specified for long-term outdoor service.
Front maintenance
Service is planned before the wall is built. Modules, cards and power supplies are replaced from the access direction agreed on the drawing.
Front service from the walkway
Modules can be released from the front where the wall faces a road or facade with no rear access. The service procedure keeps the gasket path intact.
Rear access for power and control
Where a rear walkway exists, power supplies and receiving cards are reached through a separate sealed cover without opening the module face.
Gasket and drainage checks
Service visits include a gasket inspection and drainage check. Replacement modules are supplied with the correct seal kit for the cabinet revision.
Product credibility
Documented before it ships
Outdoor P4 is built on the same production line as our project walls. Cabinets, modules and control settings are recorded per batch, and the documentation travels with the shipment so the site team is not working from memory.
ISO 9001
Factory process control
CE / RoHS / FCC
Product compliance
Batch tested
Aging and calibration record
2–3 years
Standard warranty
Quality record
- CE, RoHS and FCC documentation for the supplied configuration.
- Aging and white-balance calibration record per batch.
- Cabinet drawing, pixel map and control settings in the handover pack.
- Spare modules matched to the original production batch.
Outdoor fixed selection and delivery
Outdoor selection starts with the weather path
Brightness is only one part of an outdoor specification. Water paths, wind load, thermal expansion and service access determine whether the wall still performs after the first rainy season.
01P2.6–P10
Set brightness from the viewing direction
P2.6–P4.8 for close street viewing and building entrances; P6.67–P10 for roadside, facade and stadium distances where the nearest viewer is beyond 10 m.
02IP65 front and rear
Trace the water path
IP65 depends on gasket continuity, cable glands and cover overlap, not on a single rating label. The cabinet should shed water away from the module seam and service openings.
03Wind-load review
Confirm structure and service
Mounting points, wind load and the service route are reviewed against the installation height. Front service is used where the wall faces a road or facade with no rear walkway.
Deployment playbook
Outdoor walls where the site sets the build
A roadside billboard, a building facade and a stadium perimeter use different cabinet formats, brightness levels and service strategies.
01
Roadside and street media
The wall must stay readable in direct sun and dim at night. Automatic brightness control, high output and a sealed enclosure are the base requirements.
P4–P8 · 5,500–13,000 nits · auto dimming
02
Building facades
Wind load and fixing detail dominate. The cabinet and support frame are reviewed together, with service access planned from the facade or a maintenance walkway.
P6.67–P10 · IP65 · wind-load frame
03
Stadium perimeter
The wall is close to the pitch and on broadcast cameras. High refresh, fast-lock cabinets and a service plan for match days are part of the specification.
P4.81–P6.67 · >7680Hz · fast service
Delivery control
Outdoor build and weather test
Outdoor cabinets are assembled and sealed before packing. The factory check covers gasket continuity, cable entry and the service covers that are most likely to be opened on site.
Handover pack
- Approved cabinet layout and pixel map
- Control settings and calibration record
- Packing list, spare list and service notes
- 1
Freeze the drawing
Approved layout, pixel map and power scheduleCabinet layout, control points, power distribution and the service direction are fixed before materials are cut. The approved drawing becomes the reference for every later check.
- 2
Match the batch
Batch record and module position listLED modules, driver ICs and power supplies are drawn from the same production batch where the order size allows, then labelled by cabinet position.
- 3
Age and calibrate
Aging log and calibration fileAssembled cabinets run through an aging cycle and white-balance calibration. Faults found at this stage are corrected before packing, not after arrival.
- 4
Pack for the route
Packing list, spare list and handover packCabinets are packed against the transport method and site access. The packing list includes the seal kit, service gaskets and the fixing schedule for the approved structure.
Buyer questions
Questions we answer before quotation
These are the points that most often change the specification after the first enquiry. If your question is not here, send it with the site details.
Ask an engineer01Is IP65 enough for coastal installations?
IP65 is the starting point, but coastal sites also need corrosion protection, suitable fixings and a maintenance schedule. The cabinet finish and grounding detail are confirmed against the site conditions.
02How is wind load handled?
The mounting points and support structure are reviewed against the installation height, exposure and local requirements. The display cabinet is not specified in isolation from its frame.
03Can the wall be serviced from the front?
Yes, front-service modules are available for walls with no rear access. Where a rear walkway exists, power supplies and receiving cards can be reached through a separate sealed cover.
04What brightness is recommended for a roadside wall?
Outdoor walls can be configured from 5,500 to 13,000 nits with automatic dimming. The final setting depends on orientation, viewing distance and local brightness rules.
Next step
Plan the outdoor installation
Use the outdoor media guide and project references to confirm brightness, structure and service access.
Outdoor media guide
See how this series is specified against viewing distance, room light and installation constraints.
Open application guideInstalled references
Review project types, cabinet formats and the delivery scope used on comparable installations.
View case studiesDatasheets and drawings
Request the current specification sheet, cabinet drawing and control compatibility list.
Open downloadsTalk to an engineer
Send the wall size, viewing distance and site photos. We reply with a configuration and quotation.
Request a quoteControl-system compatibility confirmed with the quotationCE / RoHS / FCC documentation for the supplied configuration
Other Outdoor Fixed LED models
Outdoor Fixed LED
Outdoor P2.6
2.97mm · ≥7,000 cd/m²
1000 × 1000 × 90mm
Outdoor P3.9
3.91mm · ≥7,000 cd/m²
1000 × 1000 × 90mm
Outdoor P4.8
4.81mm · ≥7,000 cd/m²
1000 × 1000 × 90mm
Outdoor P5
5mm · 6,000–12,000 nits
960 × 960 × 88.5mm
Outdoor P8
8mm · 6,000–12,000 nits
960 × 960 × 88.5mm
Outdoor P6.25
6.25mm · ≥8,000 cd/m²
1000 × 1000 × 90mm
Outdoor P6.67
6.67mm · 5,500–13,000 nits
960 × 960mm
Outdoor P10
10mm · 6,000–12,000 nits
960 × 960 × 88.5mm
Request Outdoor P4 pricing and drawings
Send viewing distance, wall size and installation type. We reply with cabinet quantity, control layout and a quotation within 24 business hours.
- Factory-direct pricing
- CE / RoHS / FCC / ISO 9001
- 5–7 day lead time for standard models