01
Open LED mesh
The mesh leaves large open areas between pixels, keeping the background visible and reducing wind load on suspended installations.
Transparent LED Display Series
Holographic Transparent LED Screen
Holographic mesh that floats in the glass.
P2.5–P6.25 · 80–90% transparency · suspended mesh
A lightweight LED mesh suspended in a frame or behind glass. Content appears to float in the air, making it a strong fit for product launches, museum exhibits and flagship retail.
Transparent LED Display SeriesCrystal Film ScreenHolographic Transparent ScreenStandard Transparent Screen
Up to 95%
Transparency on crystal film
1–3mm
Film thickness, no steel frame
P2.5–P20
Pitch range across the series
- Floating image effect
- 80–90% transparency
- Lightweight aluminum frame
- Indoor and semi-outdoor
Advantages
Floating visual layer
The mesh sits in front of the background, so the subject appears suspended.
See-through structure
Visitors keep sightlines to products and architecture behind the screen.
Camera-friendly refresh
>7680Hz keeps footage clean on phones and broadcast cameras.
Simple rigging
Aluminum frame accepts truss, ceiling or floor mounting.
Holographic P3.9
Structure introduction
Holographic P3.9 is a suspended LED mesh. The mesh is held in a slim frame and hung from truss, ceiling hooks or a floor frame, so content appears to float in front of the background.
Hanging mesh, 500 × 500mm
02
Slim support frame
The frame holds the mesh at a constant tension and provides the rigging points. Frame size is set from the suspension layout, not only the screen size.
03
Rigging interface
Top and bottom attachment points accept standard clamps, hooks or floor stands. The rigging plan is confirmed against the venue structure.
04
Remote control and power
Power supplies and controllers are located off the mesh, with cabling routed along the frame or suspension points.
Design details
The decisions that affect how Holographic P3.9 looks, installs and stays serviceable on site.
01
Floating image effect
Because the mesh is suspended rather than bonded, the background stays visible and the content reads as a layer in the air.
02
80–90% transparency
The open structure keeps products, stage sets and architecture visible behind the screen.
03
Camera-friendly refresh
High refresh keeps the mesh clean on phones and broadcast cameras, which matters for launches and live events.
04
Reusable rigging
The frame and mesh can be moved between events, making the format practical for touring activations and exhibitions.
Front maintenance
Service is planned before the wall is built. Modules, cards and power supplies are replaced from the access direction agreed on the drawing.
Mesh inspection
The mesh is checked for tension and damaged pixels from the front. The frame remains hung during inspection where access allows.
Module or strip replacement
Damaged sections are replaced on the frame. Spare strips are supplied from the project batch for colour consistency.
Rigging check
Each re-hang includes a check of clamps, safety points and cable routing before power is applied.
Product credibility
Documented before it ships
Holographic P3.9 is built on the same production line as our project walls. Cabinets, modules and control settings are recorded per batch, and the documentation travels with the shipment so the site team is not working from memory.
ISO 9001
Factory process control
CE / RoHS / FCC
Product compliance
Batch tested
Aging and calibration record
2–3 years
Standard warranty
Quality record
- CE, RoHS and FCC documentation for the supplied configuration.
- Aging and white-balance calibration record per batch.
- Cabinet drawing, pixel map and control settings in the handover pack.
- Spare modules matched to the original production batch.
Applications
Flagship retail
Window and atrium feature walls.
Exhibitions
Product reveals with the booth still visible behind.
Museums
Layered graphics in front of exhibits.
Showrooms
Vehicle or equipment display with visual depth.
Model range
Each model links to its cabinet, specification and installation notes.
Holographic selection
Use the mesh when the background is part of the image
Holographic mesh is selected when the display should float in front of a product, set or architecture. The rigging and background are as important as the pixel pitch.
01Controlled background
Check the background contrast
The mesh reads best when the subject behind it is controlled and the content has a clear silhouette. Busy backgrounds reduce the floating effect and should be reviewed with a sample.
02P3.9–P6.25
Set pitch from the audience
P3.9 for closer retail and exhibition viewing; P6.25 where the audience stands farther back or the mesh is large. The frame size follows the viewing direction, not only the screen size.
03Suspended frame
Confirm the rigging points
The mesh is held in a slim frame and hung from truss, ceiling hooks or a floor frame. The venue structure and safety points are checked before the frame is detailed.
Model comparison
Compare Holographic Transparent Screen models
Pitch, power, cabinet and the job each model is specified for. Open a model to see its cabinet build, service access and quotation route.
| Model | Brightness | Avg power | Cabinet | Specified for | Detail |
|---|---|---|---|---|---|
Holographic P3.9 3.9mm | 1,500–8,000 nits | ≤260 W/m² | Hanging mesh, 500 × 500mm | Retail launches · Exhibitions | View model |
Holographic P6.25 6.25mm | 1,500–8,000 nits | ≤220 W/m² | Hanging mesh, 500 × 1000mm | Atrium suspensions · Window displays | View model |
Typical values for the current series. Final brightness, power and cabinet detail are confirmed on the approved specification sheet.
Deployment playbook
Holographic mesh in use
The format is strongest where the audience should see through the screen and the content needs to feel physically present.
01
Flagship retail
A product sits behind the mesh while graphics float in front. The window stays open and the display becomes part of the visual merchandising.
P3.9–P6.25 · 80–90% transparency
02
Museums and exhibitions
Layered graphics sit in front of an exhibit without hiding it. Content and sightlines are planned together with the curator.
P3.9–P6.25 · controlled light
03
Product launches
A vehicle or product reveal uses the mesh as a floating layer. The frame can be reused for a tour or a series of events.
P3.9–P6.25 · reusable rigging
Delivery control
Mesh frame and content mapping
The frame, mesh and pixel map are produced together. The content team receives the active area and mapping before the event build.
Handover pack
- Approved cabinet layout and pixel map
- Control settings and calibration record
- Packing list, spare list and service notes
- 1
Freeze the drawing
Approved layout, pixel map and power scheduleCabinet layout, control points, power distribution and the service direction are fixed before materials are cut. The approved drawing becomes the reference for every later check.
- 2
Match the batch
Batch record and module position listLED modules, driver ICs and power supplies are drawn from the same production batch where the order size allows, then labelled by cabinet position.
- 3
Age and calibrate
Aging log and calibration fileAssembled cabinets run through an aging cycle and white-balance calibration. Faults found at this stage are corrected before packing, not after arrival.
- 4
Pack for the route
Packing list, spare list and handover packCabinets are packed against the transport method and site access. The frame is labelled by rigging point and packed with the pixel map and re-hang checklist.
Buyer questions
Questions we answer before quotation
These are the points that most often change the specification after the first enquiry. If your question is not here, send it with the site details.
Ask an engineer01Does the mesh need a dark background?
Not necessarily, but a controlled background gives the strongest floating effect. The content and background are reviewed together, and a sample can be tested before the final specification.
02Can the mesh be hung from a ceiling?
Yes, with a frame and rigging points designed for the venue structure. The ceiling load, safety points and access for re-hanging are confirmed before production.
03Can the frame be reused?
The frame and mesh can be designed for repeated events. A re-hang checklist and labelled rigging points are included for touring or multi-site use.
04How is content mapped?
A pixel map is supplied for the active area. The content team uses it to build artwork without stretching or guessing the transparent border.
Next step
Plan the suspended display
Use the retail guide, case references and transparent white paper to confirm rigging and content mapping.
Retail and commercial guide
See how this series is specified against viewing distance, room light and installation constraints.
Open application guideInstalled references
Review project types, cabinet formats and the delivery scope used on comparable installations.
View case studiesDatasheets and drawings
Request the current specification sheet, cabinet drawing and control compatibility list.
Open downloadsTalk to an engineer
Send the wall size, viewing distance and site photos. We reply with a configuration and quotation.
Request a quoteControl-system compatibility confirmed with the quotationCE / RoHS / FCC documentation for the supplied configuration
Design a holographic display
Share the viewing distance and background. We will size the mesh and frame.