01
Transparent LED mesh
The pixel grid is laid out to leave open space between LEDs, which is what allows the glass to stay visually open when the screen is off.
Transparent LED Display Series
Crystal Film Transparent Screen
Crystal film at 95% transparency.
P4–P20 · up to 95% transparency · 3 mm film
A flexible transparent film with embedded LED pixels. It bonds to existing glass, adds almost no depth and keeps the facade visually open. Suited to retail windows, bank branches, car showrooms and office partitions.
Transparent LED Display SeriesCrystal Film ScreenHolographic Transparent ScreenStandard Transparent Screen
Up to 95%
Transparency on crystal film
1–3mm
Film thickness, no steel frame
P2.5–P20
Pitch range across the series
- Up to 95% transparency
- 3 mm film, no frame depth
- Adhesive installation on existing glass
- Indoor and semi-outdoor versions
Advantages
Keeps daylight
The open pixel grid leaves the glass usable as a window while showing content.
Fits existing glazing
No steel frame; the film is applied to the glass and connected at one edge.
Quiet visual presence
Thin profile and hidden wiring keep the shopfront clean.
Serviceable in place
Modules can be replaced without removing the whole film.
Crystal Film P6.25
Structure introduction
Crystal Film P6.25 is a laminated film, not a framed cabinet. The LED mesh, transparent carrier, adhesive layer and protective surface are bonded as one sheet that is applied directly to existing glass.
Film roll, cut to glass
02
Adhesive and carrier layers
A clear carrier holds the mesh at a consistent pitch, and the adhesive layer bonds to glass without a steel frame or visible edge.
03
Edge connection
Power and data connect along one edge through a slim ribbon. The connection is planned to sit behind a mullion or within a concealed edge trim.
04
Controller and power location
The controller and power supply are remote from the film. Their location is agreed at survey so cable routes stay hidden and serviceable.
Design details
The decisions that affect how Crystal Film P6.25 looks, installs and stays serviceable on site.
01
Up to 95% transparency
The open grid keeps daylight and sightlines through the glass. Transparency is balanced against brightness for the actual background and viewing distance.
02
3 mm film build
The film adds minimal thickness, so it can be used on shop windows and interior glass without rebuilding the frame.
03
Mullion-aware layout
The pixel map is set out around mullions and door frames so content is not cut by the building structure.
04
Removable service sections
Film sections are planned so a damaged area can be replaced without stripping the whole window.
Front maintenance
Service is planned before the wall is built. Modules, cards and power supplies are replaced from the access direction agreed on the drawing.
Glass-safe cleaning
The film surface is cleaned with a soft cloth and approved cleaner. Abrasive pads and solvent cleaners are avoided.
Section replacement
A damaged film section is removed and replaced with a matching batch section. The edge connection is reused where possible.
Controller access
The remote controller and power supply are reached without touching the glass, so routine service does not disturb the film.
Product credibility
Documented before it ships
Crystal Film P6.25 is built on the same production line as our project walls. Cabinets, modules and control settings are recorded per batch, and the documentation travels with the shipment so the site team is not working from memory.
ISO 9001
Factory process control
CE / RoHS / FCC
Product compliance
Batch tested
Aging and calibration record
2–3 years
Standard warranty
Quality record
- CE, RoHS and FCC documentation for the supplied configuration.
- Aging and white-balance calibration record per batch.
- Cabinet drawing, pixel map and control settings in the handover pack.
- Spare modules matched to the original production batch.
Applications
Retail windows
Promotions visible from the street without darkening the interior.
Bank branches
Rates and brand content on street-facing glass.
Car showrooms
Vehicle glass and partitions used as display surfaces.
Office partitions
Meeting-room glass stays translucent when the screen is off.
Model range
Each model links to its cabinet, specification and installation notes.
Crystal film selection
Specify crystal film from the glass outward
Crystal film is the right route when the glass already exists and the project cannot carry a framed cabinet. The survey, pitch and controller location decide whether the result looks clean.
01Flat existing glass
Check the glass and the background
The film works best on flat, sound glass with a background that still reads through the open pixel grid. Reflections, tint and mullions are reviewed before the pitch is chosen.
02P6.25–P10
Set pitch from the pavement
P6.25 is used where the viewer stands close to the window; P10 or larger is used where the audience is across a street or concourse. A finer pitch is not automatically better on glass.
03Edge-routed connection
Hide the edge connection
Power and data connect along one edge. The route should sit behind a mullion, frame or trim so the film reads as part of the glass rather than an applied panel.
Model comparison
Compare Crystal Film Screen models
Pitch, power, cabinet and the job each model is specified for. Open a model to see its cabinet build, service access and quotation route.
| Model | Brightness | Avg power | Cabinet | Specified for | Detail |
|---|---|---|---|---|---|
Crystal Film P6.25 6.25mm | 4,500 nits | ≤180 W/m² | Film roll, cut to glass | Shop windows · Bank branches | View model |
Crystal Film P10 10mm | 4,000 nits | ≤150 W/m² | Film roll, cut to glass | Glass facades · Bank branches | View model |
Typical values for the current series. Final brightness, power and cabinet detail are confirmed on the approved specification sheet.
Deployment playbook
Crystal film in real shopfronts
The film is chosen for existing glazing where the storefront must remain open and the installation cannot add a deep cabinet.
01
Retail windows
Promotions run after hours while the window stays visually open during the day. The film adds a media layer without rebuilding the shopfront.
P6.25–P10 · 90–95% transparency
02
Bank branches
Rates and brand content sit on street-facing glass. A clean edge route and scheduled content keep the branch front uncluttered.
P6.25–P10 · 1,000–3,000 nits
03
Car showrooms
Vehicle glass and partitions become display surfaces. The film preserves the view into the showroom while adding a transparent content layer.
P6.25–P10 · indoor or semi-outdoor
Delivery control
Film survey and dispatch
Crystal film is cut to the glass survey. The film layout, edge connection and controller position are agreed before production.
Handover pack
- Approved cabinet layout and pixel map
- Control settings and calibration record
- Packing list, spare list and service notes
- 1
Freeze the drawing
Approved layout, pixel map and power scheduleCabinet layout, control points, power distribution and the service direction are fixed before materials are cut. The approved drawing becomes the reference for every later check.
- 2
Match the batch
Batch record and module position listLED modules, driver ICs and power supplies are drawn from the same production batch where the order size allows, then labelled by cabinet position.
- 3
Age and calibrate
Aging log and calibration fileAssembled cabinets run through an aging cycle and white-balance calibration. Faults found at this stage are corrected before packing, not after arrival.
- 4
Pack for the route
Packing list, spare list and handover packCabinets are packed against the transport method and site access. Each film section is labelled by glass panel and packed with the edge connection and cleaning instructions.
Buyer questions
Questions we answer before quotation
These are the points that most often change the specification after the first enquiry. If your question is not here, send it with the site details.
Ask an engineer01Can crystal film be applied to existing glass?
Yes, that is its main use. The glass is surveyed for flatness, condition and access, and the film is cut to the panel layout before dispatch.
02Can the film be removed later?
The film can be removed as part of a planned refit, but the glass condition and adhesive residue should be assessed first. Removal and replacement are best handled by the installation team.
03How transparent is the film?
The open grid reaches up to 95% transparency depending on pitch. Higher transparency generally means less light output, so the pitch is selected against the viewing distance and background.
04Is crystal film suitable for outdoor glass?
Indoor and semi-outdoor versions are available. Full outdoor exposure requires a review of water, sun and cleaning conditions; a framed transparent cabinet may be the more suitable route.
Next step
Prepare the glass survey
Use the retail guide, transparent white paper and case references to confirm film pitch and edge routing.
Retail and commercial guide
See how this series is specified against viewing distance, room light and installation constraints.
Open application guideInstalled references
Review project types, cabinet formats and the delivery scope used on comparable installations.
View case studiesDatasheets and drawings
Request the current specification sheet, cabinet drawing and control compatibility list.
Open downloadsTalk to an engineer
Send the wall size, viewing distance and site photos. We reply with a configuration and quotation.
Request a quoteControl-system compatibility confirmed with the quotationCE / RoHS / FCC documentation for the supplied configuration
Plan a crystal film installation
Send the glass size and a photo. We will estimate film area, power and controller placement.